BATHROOM LAYOUTS · LA-21

5x10 Bathroom Layouts: Use the Length, Protect the Walkway

Fifty square feet gives you options. The five-foot width still decides where you can stand, open a drawer and get into the shower.

START HERE

A 5x10 bathroom layout works best when the fixture arrangement uses the long walls without crowding the short dimension. These three starting plans put a tub or shower across one end, then give the remaining length to a vanity and toilet. Choose between two basins, a deeper shower and more space beside the toilet; none of the drawings settles the installation details for you.

Measure the width before choosing the vanity

The drawings assume 60 × 120 inches between finished walls, approximately 152 × 305 cm. That is 50 square feet, or 4.65 m². If your measurements are to exposed studs, account for the wall assembly before comparing them with these plans. Record the door, window, drain and any boxed-in pipework separately.

Across the five-foot width, a modeled 21-inch-deep vanity leaves 39 inches to the opposite wall. Put a 30-inch-projecting toilet directly opposite it and the remaining gap drops to 9 inches. Extra length does not cure that conflict. This is why Layouts A and B stagger the fixtures along one wall instead.

What occupies the five-foot width?A 21-inch vanity leaves 39 inches to the opposite wall. Adding an opposing 30-inch toilet leaves only 9 inches between fixtures. Illustrative dimension budgets, not a proposed layout.The same width, two very different gapsIllustrative cross-sections across a 60 in finished roomVanity facing an empty wallVanity21 inRemaining floor width39 inThe same vanity facing a toiletVanity21 inGap9 inToilet projection30 inUse the long wall to stagger fixtures; extra length cannot widen this gap.
What occupies the five-foot width?A 53-centimeter vanity leaves 99 centimeters to the opposite wall. Adding an opposing 76-centimeter toilet leaves only 23 centimeters between fixtures. Illustrative dimension budgets, not a proposed layout.The same width, two very different gapsIllustrative cross-sections across a 152 cm finished roomVanity facing an empty wallVanity53 cmRemaining floor width99 cmThe same vanity facing a toiletVanity53 cmGap23 cmToilet projection76 cmUse the long wall to stagger fixtures; extra length cannot widen this gap.
Original BathDraft comparison. These are illustrative projections, not a complete floor plan. Measure the actual countertop, handles and toilet before substituting products.

The dashed rectangles in the plans are the planner’s simplified clearance overlays. Local adopted rules, accessibility needs and actual product instructions still govern the project. Use our bathroom dimensions guide for the broader measurement checklist.

Three plans, with different compromises

All three retain a 30-inch room door in the middle portion of the right-hand wall. Its location matters: a bathroom labeled “10x5” has the same area, but a door on another wall is a different design problem. Open a drawing in the Bathroom Layout Planner and enter your own opening before judging the result.

Layout A: keep the tub and put two sinks along the wall

A 5 by 10 foot bathroom with a 60 inch tub across the end and a 60 inch double vanity and the toilet on one long wall5 ft · 60 in10 ft · 120 in21 in21 inTUB 60×3060″ VANITY15 in15 in
A 5 by 10 foot bathroom with a 60 inch tub across the end and a 60 inch double vanity and the toilet on one long wall1.52 m3.05 m53 cm53 cmTUB 152×76 cm152 cm VANITY38 cm38 cm
A 60 × 30-inch tub block, 60-inch vanity and elongated toilet use one long side of the room.
Open Layout A in the planner

This arrangement suits a household that wants to keep bathing and two washbasins in one room. The modeled sink centers are 30 inches apart. The toilet centerline sits 15 inches from both the vanity end and the entrance-end wall, with 30 inches between its front and the opposite wall.

Those side spaces leave little room for product substitutions. A longer countertop, a projecting towel bar or a shifted toilet flange can change the result. The plan also treats the tub as exactly 60 × 30 inches; use the chosen tub’s rough-in drawing, installation opening and finished apron dimensions rather than its sales label. A fixture lineup on one wall does not establish the cost or feasibility of the drainage route.

Layout B: choose one basin and a deeper shower

A 5 by 10 foot bathroom with a 60 by 36 inch walk-in shower across the end, a 48 inch vanity and the toilet on one long wall5 ft · 60 in10 ft · 120 in24 in21 in21 inSHOWER 60×3648″ VANITY18 in18 in
A 5 by 10 foot bathroom with a 60 by 36 inch walk-in shower across the end, a 48 inch vanity and the toilet on one long wall1.52 m3.05 m61 cm53 cm53 cmSHOWER 152×91 cm122 cm VANITY46 cm46 cm
A nominal 60 × 36-inch shower block leaves room for a 48-inch vanity along the left wall.
Open Layout B in the planner

Here, the shower takes six more inches of room length than Layout A’s tub. Reducing the vanity by twelve inches leaves the toilet centerline 18 inches from the vanity end and 18 inches from the far wall. For someone who values one usable basin and counter space over two basins, this is the first arrangement I would mock up.

Check the shower opening on the right-hand portion of its frontage: the vanity is immediately beside the left-hand portion. The drawing’s long clear strip is not clearance across the entire shower width. Specify a compatible enclosure and its opening position, then test its operation with the room door. A nominal 36-inch shower depth also does not prove a 36-inch finished interior.

Layout C: put the double vanity at the opposite end

A 5 by 10 foot bathroom with a 60 by 32 inch shower at one end, a 60 inch double vanity across the other end and the toilet between them5 ft · 60 in10 ft · 120 in24 in21 in21 inSHOWER 60×3260″ VANITY22 in45 in
A 5 by 10 foot bathroom with a 60 by 32 inch shower at one end, a 60 inch double vanity across the other end and the toilet between them1.52 m3.05 m61 cm53 cm53 cmSHOWER 152×81 cm152 cm VANITY56 cm114 cm
The 60 × 32-inch shower and 60-inch vanity occupy opposite ends. The toilet remains on the left wall.
Open Layout C in the planner

This separates washing from showering, but the end-wall vanity is the difficult purchase. The modeled sinks sit 15 inches from the side walls. Many products sold as a “60-inch double vanity” have different sink positions or a wider top.

For example, Kohler’s Hearthaven K-33539-ASB specification shows a 60 9/16-inch top. That top cannot fit between walls exactly 60 inches apart. Its sink-center positions also differ from this plan. This is a dimension-check example, not a product recommendation. Obtain the full drawing before reserving a wall-to-wall opening.

The toilet’s center is 22 inches from the shower edge, and its front is 30 inches from the right wall. Yet the doorway and shower approach share that side of the room. Walk through both sequences—entering the room and leaving the shower—with the door and enclosure represented at full size.

Look above the floor plan, too

Fifi McGee’s demonstration at about 3:20–3:40 explains why a deep mirror cabinet can be awkward above a shallow basin. For this five-foot-wide room, gaining floor space with a shallower vanity should trigger a second check: mock up the cabinet projection while leaning over the basin. The video illustrates that interaction; the measurements in our plans come from BathDraft’s own geometry.

Video by Fifi McGee | Interior Design & Renovations. Watch the original on YouTube.

Test these details before ordering

CheckWhat to put on the drawing
Finished roomWall-to-wall dimensions at several points; allow for uneven walls and the proposed finish.
VanityOverall top width and depth, sink centers, handles and the full open-drawer position.
ToiletActual projection, flange rough-in and centerline distances to nearby obstructions.
Shower or tubInstallation opening, finished interior, access position and enclosure movement.
Daily useSpace to dry off, reach a towel and pass another person without opening a door into them.

Tape the main footprints on the floor, then use cardboard to represent the vanity and opened drawers. Test the room with the person who will use it, including a helper if relevant. NKBA’s published guidance separates more generous planning recommendations from code references; a minimum-distance result alone does not establish that a room will work for your household.

What changes if the room is 5x11?

An extra foot adds five square feet and twelve inches along the long axis. You can assign that length to a larger vanity, more separation or storage, but it does not widen the five-foot route. It also does not automatically make a separate tub and shower fit: that requires a new arrangement using the actual fixtures, opening and plumbing constraints.

If a bath and shower are both priorities, first compare a shower-over-tub arrangement with the compromises of separate fixtures. For nearby footprints, see the 5x8 layout guide and 5x9 plans. Our long, narrow bathroom guide covers the broader choice of fixture sequence.

Final Takeaway

Start with Layout A if the tub and two sinks matter most, B if a deeper shower and one basin suit your routine, or C if you want the washing area at the far end. Then replace every generic block with the selected product’s dimensions. In a 5x10 bathroom, the winning plan is the one that leaves usable space at its narrowest point and still works with the doors open.

Main Sources

Plans and width comparison are original BathDraft illustrations. Generic fixture blocks are starting assumptions; the diagrams are not installation drawings.