BATHROOM LAYOUTS · LA-24

How to Make a 6x10 Bathroom Work for Your Routine

A longer tub, a separate shower, two sinks or laundry: these four plans show where each choice gains space—and where the six-foot width still limits it.

PLAN AROUND YOUR ROUTINE

A 6x10 bathroom is 72 × 120 inches, or 60 square feet, about 5.6 m². It can support several arrangements, but fitting more fixtures does not guarantee more usable space. Compare the four examples below against the task that matters most: bathing, showering, getting ready together or doing laundry.

Decide what the extra length should do

Start with the doorway and existing plumbing. If the tub is already across the end, A may preserve a familiar arrangement. B adds a separate shower but narrows the floor between the toilet and vanity. C gives the tub’s space to a shower and second sink. D brings laundry into the bathroom.

Measure between finished walls, then mark the window, door swing and obstructions in the bathroom layout planner. A ten-foot room offers a longer fixture run; it does not make its six-foot width any wider. Check both directions before selecting cabinets.

These are nominal fixture blocks, with a 21-inch-deep vanity, 30-inch toilet projection and 30-inch entry-door leaf. Dashed zones are selected reference spaces, not complete installation checks. On narrow screens, scroll each drawing sideways; keyboard users can focus the diagram and use the arrow keys.

Four layouts with different priorities

A 6 by 10 foot bathroom with a 72 by 36 inch tub across the end and a 48 inch vanity and the toilet on one long wall6 ft · 72 in10 ft · 120 in21 in21 inTUB 72×3648″ VANITY18 in18 in
A 6 by 10 foot bathroom with a 72 by 36 inch tub across the end and a 48 inch vanity and the toilet on one long wall1.83 m3.05 m53 cm53 cmTUB 183×91 cm122 cm VANITY46 cm46 cm
Layout A: a nominal 72 × 36-inch tub, 48-inch vanity and toilet. The vanity has 51 inches to the opposite wall.
Open Layout A in the planner

A. Put a longer tub first

The tub occupies the far end, with the vanity and toilet following along the right wall. This keeps the opposite side clear of fixture blocks. Across the vanity, the gap is 72 − 21 = 51 inches; across the toilet, it is 42 inches. The toilet center is 18 inches from the entrance wall.

The nominal tub uses all 72 inches of room width. That is a product-selection constraint, not proof of an exact installation fit. Kohler’s 7236 specification calls its dimensions nominal and requires measuring the actual product for rough-in. Check the flange, framing and finished wall build-up with the installer.

A tub’s outer length also differs from its usable basin. Compare the bathtub measurements before choosing the longer model. Keep this arrangement for bathing you expect to enjoy, rather than taking the largest label the end wall appears to accept.

A 6 by 10 foot bathroom with a 60 inch tub across the end, a separate 36 inch shower in the far corner, a 48 inch vanity and the toilet6 ft · 72 in10 ft · 120 in24 in21 in21 inTUB 60×30SHOWER 36×3648″ VANITY18 in72 in
A 6 by 10 foot bathroom with a 60 inch tub across the end, a separate 36 inch shower in the far corner, a 48 inch vanity and the toilet1.83 m3.05 m61 cm53 cm53 cmTUB 152×76 cmSHOWER 91×91 cm122 cm VANITY46 cm183 cm
Layout B: a 60-inch tub, 36-inch shower and 48-inch vanity. The toilet and vanity face across a 21-inch gap.
Open Layout B in the planner

B. Add a separate shower and accept a narrower middle

The tub occupies 60 of the 72 inches along the far wall, leaving a 12-inch remainder. A square shower sits near the entrance. Between the two bathing areas, the vanity faces the toilet across 72 − 21 − 30 = 21 inches.

That gap deserves a physical mock-up. Check sitting, standing and opening a drawer while another person uses the basin. A shallower vanity would widen the modeled gap, but its basin, faucet and storage still need to suit daily use.

The selected shower approach extends 36 inches to the opposite wall. It does not include a chosen enclosure’s swing or a person stepping out. Resolve the shower and room doors together. For other ways to divide the bathing areas, compare our tub and separate shower layouts.

A 6 by 10 foot bathroom with a 60 by 36 inch walk-in shower and a 60 inch double vanity on one long wall and the toilet on the end wall6 ft · 72 in10 ft · 120 in24 in21 in21 inSHOWER 60×3660″ VANITY18 in18 in
A 6 by 10 foot bathroom with a 60 by 36 inch walk-in shower and a 60 inch double vanity on one long wall and the toilet on the end wall1.83 m3.05 m61 cm53 cm53 cmSHOWER 152×91 cm152 cm VANITY46 cm46 cm
Layout C: a 60-inch shower run and 60-inch double vanity fill the ten-foot wall. Installation details need their own allowance.
Open Layout C in the planner

C. Trade the tub for two sinks

The shower and vanity divide the right wall equally. Their nominal lengths add to 120 inches, leaving no spare length for a separating assembly, filler or installation tolerance. Check the actual finished opening and cabinet top, not just the advertised width.

The modeled basin centers are 30 inches apart, with the outer centers 15 inches from the shower edge and end wall. A real double vanity can place its bowls differently. Consider whether two simultaneous users would be better served by one basin and more counter space.

The vanity has 51 inches to the opposite wall, but the shower frontage is less straightforward. Near the toilet, the gap to the shower block is only 9 inches; the reported 36-inch approach occurs farther along the shower. Its entrance must suit that usable section. The fully open room-door line also meets the vanity front, so handles and thickness need checking.

A 6 by 10 foot bathroom with a 60 inch tub along one long wall, a 36 inch vanity, the toilet and a stacked washer and dryer6 ft · 72 in10 ft · 120 in21 in21 in25 inTUB 60×3036″ VANITYSTACKED W/D18 in21 in
A 6 by 10 foot bathroom with a 60 inch tub along one long wall, a 36 inch vanity, the toilet and a stacked washer and dryer1.83 m3.05 m53 cm53 cm64 cmTUB 152×76 cm91 cm VANITYSTACKED W/D46 cm53 cm
Layout D: a 60-inch tub, 36-inch vanity, toilet and generic 29 × 37-inch stacked-laundry envelope.
Open Layout D in the planner

D. Give laundry a place in the bathroom

The tub and vanity sit at the far end; the toilet and laundry stack occupy the entrance end. The closed laundry envelope faces the vanity across 120 − 37 − 21 = 62 inches. This is a gap between blocks, not the remaining floor with an appliance door open.

For comparison, LG’s WM4000H sheet lists a 30¼-inch body depth, 55-inch door-open depth, at least 4 inches behind and 1 inch at the sides. The complete washer/dryer pair, stacking kit and connections determine the final envelope.

Check overhead space, controls, service access and the dryer’s ventilation route. Then test loading with a basket while the bathroom door is open. Our bathroom laundry guide covers the shared-space decision in more detail.

Compare the floor between fixtures

Both A and B are six feet wide. What changes is whether a toilet projects into the space opposite the vanity. The diagram isolates that decision; it does not represent every section of either room.

Six feet across can leave a 21-inch gapWidth comparison at selected fixture sections. Layout B has a 30-inch toilet projection, 21-inch gap and 21-inch vanity depth. A single-wall vanity in Layout A leaves 51 inches to the opposite wall. These are selected sections, not whole-room clearances.Six feet across can leave a 21-inch gapCompare across the fixtures, not along the room.LAYOUT B · TOILET OPPOSITE VANITYToilet projection30 inFacing gap21 inVanity depth21 in72 in total finished widthLAYOUT A · VANITY OPPOSITE OPEN WALLOpen floor at this section51 inVanity depth21 in72 in total finished widthNominal blocks. Check actual products, drawers and doorways separately.Original BathDraft section diagram; not a permit or accessibility assessment.
A 183 cm room can leave a 53 cm gapIn the illustrated room, 183 centimeters wide, a toilet projecting 76 centimeters opposite a vanity 53 centimeters deep leaves a gap of 53 centimeters. With only the vanity at this cross-section, the gap is 130 centimeters. Values are rounded.A 183 cm room can leave a 53 cm gapCompare across the fixtures, not along the room.LAYOUT B · TOILET OPPOSITE VANITYToilet projection76 cmFacing gap53 cmVanity depth53 cm183 cm total finished widthLAYOUT A · VANITY OPPOSITE OPEN WALLOpen floor at this section130 cmVanity depth53 cm183 cm total finished widthRounded metric values. Check products, drawers and doorways separately.Original BathDraft section diagram; not a permit or accessibility assessment.
Original BathDraft section study. The 21-inch gap in B and 51-inch gap at A’s vanity come from the same 72-inch width.

NKBA recommends 30 inches of clear floor in front of fixtures. Its published guide distinguishes recommendations from model-code references. Check locally adopted requirements separately.

Moving from a 6x8 bathroom to a 6x10 adds 12 square feet along the room’s length. The gap between the same opposing fixtures stays unchanged because the width is still 72 inches. Likewise, writing the dimensions as “10x6” does not relocate a real doorway or drain. Hold those fixed points in place when comparing a rotated drawing.

Check how laundry reaches the room

LG’s demonstration checks doors, hallways, turns and the installation space. Watch 0:07–0:46 before choosing Layout D. Apply the measuring method to your delivery route and opening movements, then use the selected model’s instructions for dimensions; the video’s general allowances do not replace them.

LG USA: How to Measure for Installation.

Final Takeaway

Use A for a longer bath, investigate B when separate bathing areas matter, compare C for two sinks, or choose D when laundry belongs in the routine. The decisive measurement is often the narrowest part of the chosen arrangement. Verify the actual products and opening movements there before ordering.

Main Sources

The plans and width diagram are original BathDraft examples. Their measurements do not establish installation approval or accessibility.