BATHROOM LAYOUTS · LA-30

6x7 Bathroom Layouts: Where You Gain Room to Move

A bigger vanity can leave a smaller place to stand. These four plans compare the trade-offs inside a 6 by 7 foot bathroom, including a tub arrangement worth testing before choosing a longer counter.

THE ANSWER

A 6x7 bathroom provides 42 sq ft within a 72 × 84 in rectangle. In these examples, putting the vanity and toilet on opposite end walls leaves a 33 in facing gap. Putting them on opposite long walls reduces that gap to 21 in, despite allowing a wider vanity. Start with Layout A for a tub or Layout D for a shower, then compare the doorway and plumbing with your room.

A / D facing gap33 in
B / C facing gap21 in
Illustrative plans4 options
Floor area42 sq ft6 × 7 ft
Stationary fixture measurements; doors checked separatelyLA-30

The useful difference is which way the fixtures face

Each example uses a 21 in deep vanity and a toilet projecting 30 in from its wall. Across the 84 in room length, subtracting both footprints leaves 33 in. Across the 72 in width, it leaves 21 in. The room has not shrunk; the fixtures are using its shorter dimension.

On small screens, scroll diagrams sideways to read all the labels.

Same fixture depths, different facing gaps in four 6x7 examples Layouts A and D face the vanity and toilet across 84 in, leaving 33 in. Layouts B and C face them across 72 in, leaving 21 in. The vanity projects 21 in and the toilet 30 in in both examples. Doors, users and fittings are not included. Orientation changes the facing gap Layouts A / D: facing across 84 in Vanity 21 in Gap 33 in Toilet 30 in 84 in − 21 in − 30 in = 33 in Layouts B / C: facing across 72 in Vanity 21 in Gap 21 in Toilet 30 in 72 in − 21 in − 30 in = 21 in Stationary footprints only. Opening doors, drawers and people need separate checks.
Same fixture depths, different facing gaps in four 6x7 examples Layouts A and D face the vanity and toilet across 213 cm, leaving 84 cm. Layouts B and C face them across 183 cm, leaving 53 cm. The vanity projects 53 cm and the toilet 76 cm in both examples. Doors, users and fittings are not included. Orientation changes the facing gap Layouts A / D: facing across 213 cm Vanity 53 cm Gap 84 cm Toilet 76 cm 213.36 − 53.34 − 76.20 = 83.82 cm Layouts B / C: facing across 183 cm Vanity 53 cm Gap 53 cm Toilet 76 cm 182.88 − 53.34 − 76.20 = 53.34 cm Stationary footprints only. Opening doors, drawers and people need separate checks.
Original BathDraft comparison. These are gaps between stationary fixture fronts, before accounting for an opening door, drawer or person.

A 21 in front space appears in the model-code guidance summarized by NKBA’s bathroom planning guidelines; its design recommendation is 30 in. Neither figure establishes comfortable shared use. Where 21 in is the applicable minimum, an uncounted countertop overhang or deeper toilet can erase the margin. Local requirements and accessibility needs may demand a different arrangement.

Measure the finished room first, then record the doorway and plumbing locations. If your “6x7” measurement is between studs, allow for the proposed wall buildup. Use actual installed projections from product drawings; the toilet dimensions guide explains the measurements to check.

Four layouts to compare in the planner

The drawings retain the same room and fixture blocks so the trade-offs remain visible. Dashed zones represent selected clearance checks, not a complete code review. All four have a modeled 30 in inward-opening door. Open a plan in the bathroom layout planner, then enter your measurements.

On a narrow screen, swipe a diagram sideways. Keyboard users can focus the diagram and use the arrow keys.

A 6 by 7 foot bathroom with a 60 inch tub along the 7 foot wall, a 42 inch vanity on one end wall and the toilet on the other6 ft · 72 in7 ft · 84 in21 in21 inTUB 60×3042″ VANITY18 in24 in
A 6 by 7 foot bathroom with a 60 inch tub along the 7 foot wall, a 42 inch vanity on one end wall and the toilet on the other1.83 m2.13 m53 cm53 cmTUB 152×76 cm107 cm VANITY46 cm61 cm
Layout A: 60 × 30 in tub, 42 in vanity and a toilet on opposite end walls.
  • Facing gap: 33 in
  • Toilet centerline to tub edge: 18 in
Open Layout A in the planner

A: keep the tub and gain standing space

The 60 in tub runs along the 7 ft wall. Beside it, the 42 in vanity faces the toilet across the longer room dimension. This is the first tub option I would compare when the entrance can stay on the long wall opposite the bath.

The trade-off is the doorway: it swings into the central floor. Its simplified arc misses the fixture blocks, but someone standing at the basin still needs somewhere to move. Test the door handle, vanity drawers and towel storage together. The 24 in beyond the tub’s end is not automatically spare cabinet space; the toilet also uses that end of the room.

A 6 by 7 foot bathroom with a 60 inch tub across the 6 foot end and a 48 inch vanity facing the toilet6 ft · 72 in7 ft · 84 in21 in21 inTUB 60×3048″ VANITY18 in36 in
A 6 by 7 foot bathroom with a 60 inch tub across the 6 foot end and a 48 inch vanity facing the toilet1.83 m2.13 m53 cm53 cmTUB 152×76 cm122 cm VANITY46 cm91 cm
Layout B: 60 × 30 in tub with a 48 in vanity facing the toilet.
  • Facing gap: 21 in
  • Toilet centerline to tub edge: 18 in
Open Layout B in the planner

B: choose a wider vanity with a tighter aisle

Turning the tub across the 6 ft end wall makes room for a 48 in vanity along one side. The toilet faces it, leaving only 21 in between the fronts. That counter gains 6 in of width over Layout A while the facing gap loses 12 in.

The tub block also leaves a 12 in strip at one end. A real alcove tub needs its specified support and enclosure; do not assume it can simply sit in that oversized opening. Added framing or a ledge must be drawn into the plan. The vanity shown is one workable example to investigate, not the maximum width every 6x7 bathroom can take.

A 6 by 7 foot bathroom with a 72 by 36 inch soaking tub across the end and a 48 inch vanity facing the toilet6 ft · 72 in7 ft · 84 in21 in21 inTUB 72×3648″ VANITY18 in30 in
A 6 by 7 foot bathroom with a 72 by 36 inch soaking tub across the end and a 48 inch vanity facing the toilet1.83 m2.13 m53 cm53 cmTUB 183×91 cm122 cm VANITY46 cm76 cm
Layout C: nominal 72 × 36 in tub footprint. Confirm the actual installation opening separately.
  • Facing gap: 21 in
  • Toilet centerline to tub edge: 18 in
Open Layout C in the planner

C: investigate a longer tub before committing

This footprint study replaces the smaller bath with a 72 × 36 in block. The deeper tub shifts the 48 in vanity and toilet 6 in toward the entrance. The facing gap remains 21 in, and the vanity reaches the entrance wall.

A nominal 72 in tub is not a confirmed fit in a 72 in finished room. For example, Kohler’s 7236 bath specification labels its dimensions nominal and calls for measuring the actual product for rough-in details. Stud opening, flange, wall finish and installation sequence need to agree with the selected model. Check the bathtub size guide, then have the installer verify the opening before ordering.

A 6 by 7 foot bathroom with a 60 by 36 inch walk-in shower along the 7 foot wall, a 36 inch vanity on one end wall and the toilet on the other6 ft · 72 in7 ft · 84 in24 in21 in21 inSHOWER 60×3636″ VANITY15 in21 in
A 6 by 7 foot bathroom with a 60 by 36 inch walk-in shower along the 7 foot wall, a 36 inch vanity on one end wall and the toilet on the other1.83 m2.13 m61 cm53 cm53 cmSHOWER 152×91 cm91 cm VANITY38 cm53 cm
Layout D: 60 × 36 in shower footprint with a 36 in vanity.
  • Vanity-to-toilet facing gap: 33 in
  • Toilet centerline to shower edge: 15 in
Open Layout D in the planner

D: prioritize showering, then resolve the entrance

The shower takes 6 in more room depth than Layout A’s tub. The vanity narrows to 36 in, while the gap in front of it remains 33 in. Beside the shower, the toilet centerline is only 15 in from its edge.

The outer base footprint does not establish the finished shower interior or entry width. Glass, wall lining and the chosen enclosure can change both. This drawing also omits the shower-door swing. Add that operation before accepting the arrangement; an outward-opening shower door must not trap someone against the vanity or conflict with the room door.

Try the door and controls before choosing finishes

If Layout B suits the existing plumbing but its aisle feels tight, test a shallower vanity before merely making it narrower. Changing the modeled depth from 21 to 18 in would increase the facing gap from 21 to 24 in, assuming the same toilet and room dimensions. Reducing its width alone would not change that gap. Check basin usability, storage and the complete countertop projection before accepting the shallower option.

A room labeled 7x6 has the same floor area, but the entrance may be on the opposite type of wall. Rotate a whole drawing only if the door, window and service locations rotate with it; otherwise start by placing those fixed features.

In Layouts B and C, the fully open room-door line lies along the vanity-front boundary. The drawing has no allowance for a projecting handle, door thickness or cabinet hardware. Tape out the footprints and swing a cardboard door template; try standing at the sink while another person enters.

For the shower plan, Reynard Lowell’s video makes a useful extra check. From 5:24–6:11, he demonstrates locating controls where they can be reached from the entrance without standing under the initial spray, while remaining reachable during a shower. Mock up that reach in Layout D alongside the vanity and shower opening. This is a usability check, not a prescribed mounting position or code measurement.

Reynard Lowell, 11 Bathroom Design Regrets & Costly Mistakes To Avoid. Watch the controls example at 5:24. Watch on YouTube.

Final Takeaway

For these 6x7 examples, Layout A gives a useful balance of tub, counter and standing space. Layout B trades aisle space for a wider vanity; C requires a separate tub-installation check. Layout D suits a shower priority once its enclosure and entry are resolved. Choose with your actual doorway and product drawings, then confirm local requirements before construction.

Main Sources

Plans and facing-gap calculations are BathDraft examples. They do not establish construction approval, accessibility or the largest possible fixture sizes.