BATHROOM LAYOUTS · FREE TOOL · LA-01

Bathroom layout planner

Enter your bathroom’s size and door, pick the fixtures, and see the layouts it finds that fit, drawn to scale. Drag a fixture to try your own idea: the planner rechecks its clearances as you go.

1. Your room
Width (the wall drawn across the top)
ft
in
Length
ft
in

Measure wall to wall at floor level, above the baseboard, the finished walls if the room is being rebuilt.

2. The door
in
3. Fixtures
The planner tries each fixture on each wall at a set of positions.

How to measure your bathroom

  1. Wall to wall, both ways. Measure at floor level, just above the baseboard, and write down the smaller number if the walls aren’t square.
  2. The door. Note which wall it’s on, how far its opening starts from the nearest corner, the door’s width, and whether it swings in, swings out or slides.
  3. The plumbing wall. Note the wall with the drain and supply lines. Keeping usable existing plumbing locations can reduce work, but the drain, vent and structure still need checking.
  4. The fixtures. Check the depth of the toilet you’ll buy, from the wall to the front of the bowl: about 28 in for a round bowl and about 30 in for an elongated one on Kohler’s and TOTO’s sheets. Check the vanity, tub or shower base on its maker’s sheet too.

How to design a bathroom layout in five steps

  1. Start from the plumbing wall. Keeping usable existing drain and supply locations can reduce work. The planner ranks layouts with fewer plumbing walls first, but this is a rough preference rather than a cost estimate; joists, slab work, vent routes and access can change the cost.
  2. Settle the door. A 30 in door that swings into a 5 ft wide room sweeps half its width. If nothing fits, compare a different hinge position or door type. An outward swing needs a clear hall, and a pocket door needs a suitable wall cavity without conflicting pipes or wiring.
  3. Place the biggest fixture first. A 60 in tub or shower usually runs wall to wall across one end of the room.
  4. Fit the toilet and the vanity with their clear space. The selected 2021 IRC rules ask for 15 in from the toilet’s centerline to a wall or the next fixture and 21 in of clear floor in front of the toilet and the sink. Designers aim for 18 in and 30 in.
  5. Add storage that doesn’t take floor. A recessed medicine cabinet, a shower niche or shelves over the toilet leave the clear spaces open.

What the planner checks

A passing result means the plan passes the dimensional checks modeled here. It is not building-code approval. Residential dimensions use selected 2021 IRC spacing rules; Comfortable adds planning recommendations. Accessibility dimensions screen selected ADA floor-space requirements. None of these modes checks a complete building, installation or accessible route.

The sink accessibility screen tests a 30 × 48 in approach against the room and surrounding fixtures. Closed vanity cabinets do not receive assumed knee space. The wall-mounted sink option assumes an open underside for this preliminary floor-plan check; actual knee and toe profiles, mounting height, pipe protection, taps and reach still need separate review.

CheckResidential dimensionsComfortableAccessibility dimensions
Toilet centerline to a wall or fixture15 in (IRC R307.1)18 in (NKBA)16 to 18 in to a side wall (ADA 604.2)
Clear floor in front of the toilet21 in (IRC R307.1)30 in (NKBA)60 × 56 in around the toilet (ADA 604.3.1)
Sink centerline to a wall or fixture15 in (IRC R307.1, P2705.1)20 in (NKBA)Not set
Two sinks, center to center30 in (IRC P2705.1)36 in (NKBA)Not set
Toilet to a sink beside it, center to center30 in (IRC P2705.1)Not setNot set
Clear floor in front of a sink or vanity21 in (IRC R307.1)30 in (NKBA)30 × 48 in (ADA 305.3, 606.2)
Clear floor in front of a shower24 in (IRC R307.1)30 in (NKBA)Depends on the shower type (ADA 608.2)
Shower floor900 sq in, at least 30 in across (IRC P2708.1)36 × 36 in inside (NKBA)Transfer 36 × 36 in; roll-in 30 × 60 in (ADA 608.2)
Clear floor in front of a washer and dryerRoom to open the doors: about 25 in, or 21 in for 24 in machines (makers’ sheets)36 in (NKBA walkway)30 × 48 in, side approach (ADA 611.2)
Turning spaceNot setNot setA 60 in circle (ADA 304.3)
DoorNo minimum width for a bathroom door (IRC R311.2 covers the exit door only)32 in clear (NKBA)32 in clear (ADA 404.2.3)

NKBA numbers come from the National Kitchen & Bath Association’s free bath planning guidelines; its newer, paid editions ask for a little more in places, such as a 34 in clear door opening. For a hinged door, this tool estimates the clear opening by subtracting 2 in from the nominal leaf width. Measure the actual opening with the door at 90 degrees; the estimate is not a guarantee. The planner also checks that each fixture is inside the room, nothing overlaps, the drawn entry door does not hit modeled fixtures and a simplified route connects the door to the fixtures. Its 18 in route width, narrowed to 14 in past lower fixtures, is only a permissive search heuristic. These widths are not recommended circulation widths, code minima or accessible-route dimensions. Codes are adopted and amended locally: your building department has the final say.

How the planner reads the spacing rules for a sink. A wall, a shower wall, a partition, a linen cabinet or another sink counts beside a sink for its 15 in. A tub’s low rim doesn’t, and neither does a toilet on the other side of a vanity cabinet: the cabinet separates them, and the toilet keeps its own 15 in from the cabinet. A toilet and a sink side by side on one wall still need 30 in from center to center, cabinet or not, because the code counts them as adjacent fixtures (P2705.1). Inspectors don’t all read these rules the same way, so check with yours.

Start from a measured layout

Each layout guide has plans drawn by this planner, ready to open and adjust: bathroom layout ideas by room size, small bathroom layouts, 5x8 bathroom layouts, 5x7 bathroom layouts, 8x8 bathroom layouts, master bathroom layouts, layouts with a tub and a separate shower, long narrow bathroom layouts, Jack and Jill bathrooms, ensuite bathrooms, 3/4 and half baths, half bath dimensions, powder room layouts and ADA bathroom layouts.

What the planner doesn’t do

  • It doesn’t design plumbing, venting or wiring. Moving a drain or a vent, and any electrical work, is a job for a licensed plumber or electrician, usually with a permit.
  • It draws rectangular rooms with fixtures against the walls, and no angled walls. Plans from our layout guides can add a partition wall (for a toilet room) or a freestanding tub, and they open here too, but the form doesn’t place those for you yet.
  • Fixture sizes are typical nominal sizes. Check the spec sheet of what you buy, especially the toilet’s depth and the shower base’s inside size.
  • Corner (neo-angle) showers come in 38 and 42 in sizes, drawn with a typical angled front. This catalog does not offer a 36 in corner model. A nominal outside dimension alone does not establish the finished shower’s clear width and area; check the chosen base and enclosure.
  • It does not model shower-enclosure door swings, cabinet doors and drawers, tub-entry movements or the space outside an outward-opening entry door. Check each operating position separately.
  • It screens selected model-code dimensions, not every requirement. It does not establish local code compliance, complete ADA compliance, structural support, waterproofing, ventilation or a safe route outside the room.

Questions

How do you design a bathroom layout?

Start from the wall that has the plumbing, settle the door, place the tub or shower first, then fit the toilet and vanity with 15 in from the toilet’s centerline to anything beside it and 21 in of clear floor in front of each. The planner screens these dimensions and shows candidate arrangements; it does not check every installation or code requirement. It tries a set of positions, so it can miss a layout that needs an unusual one.

How much space do you need around a toilet?

At least 15 in from the center of the toilet to a side wall or the next fixture, and 21 in of clear floor in front of it, under the 2021 International Residential Code (R307.1). The NKBA recommends 18 in and 30 in for a comfortable bathroom.

Can the bathroom door swing over the toilet?

The residential code doesn’t forbid a door swinging over a fixture’s clear floor, but the door can’t hit the fixture itself. The planner flags a door that hits a fixture and suggests swinging it the other way, out, or switching to a pocket door. Accessible bathrooms have stricter rules (ADA 603.2.3).

Does a tub need clear space in front of it?

The 2021 International Residential Code sets no clear space for a tub, only for toilets, sinks and showers. The planner still checks that you can walk from the door to the tub.

How wide does a bathroom door have to be?

The residential code sets no minimum for an inside door such as a bathroom door; only the main exit door needs 32 in (IRC R311.2). The NKBA recommends a 32 in clear opening, and accessible bathrooms need one (ADA 404.2.3), which takes a 34 or 36 in door.

Is the planner free, and do I need an account?

Yes, it’s free, and there’s no account. Plans you save go to My bathroom in your browser, and a share link carries the whole plan in the address.

Can I use centimeters?

Yes. Switch to cm at the top of the page: the fields, the drawing and the checks all change over.

Main Sources